Pilot Assembly Replacement in Alamo Heights, TX

Classic weak-thermocouple behavior. The pilot lights fine, but the thermocouple no longer generates enough millivolt output to hold the gas valve's safety magnet open, so the instant you stop holding the knob down as an override, the valve snaps shut. We put a meter on it — a healthy thermocouple reads around 25-30 mV open-circuit — and swap the failed proving part on the ignition you already have. For this exact symptom, that's the fix we make most often.

One is a parts swap, the other is construction. Here we replace a worn component on your existing ignition — the thermocouple, thermopile, igniter, or pilot hood that finally aged out — without touching how the fireplace lights. Pilot light installation is the opposite case: building a whole new system where nothing works. When the architecture is sound and a single part has died, you're on the right page.

Because nine times out of ten the culprit is the inexpensive proving part, not the valve itself. A dropping pilot usually traces to a weak thermocouple, which this service fixes; less often it's a valve magnet that won't hold even with a healthy millivolt signal, and that's valve work. Metering the thermocouple output and checking the valve's hold tells us which one to replace — and we rule out a clogged orifice or a stray draft before touching either.

Swapping the thermocouple only helps if the sensor was the actual problem. A clogged pilot orifice, a draft blowing the flame off the sensor tip, low gas pressure, or a tired valve magnet will all keep the pilot dropping out with a brand-new part in place. That is why our crew re-reads the millivolt output after the swap and adjusts the flame so it fully wraps the sensor, and when the hood and orifice are worn along with it, we replace the whole hood-and-thermocouple assembly instead of just the single piece.

That's the whole design of it. Older homes interconnect in ways separate contractors miss — the chase that carries your original flue often carries duct runs and wiring too, and an uninsulated attic changes how the entire house breathes. We inspect chimney, ducts, dryer vent, and insulation in one pass and write it up as one prioritized report, so you're not reconciling four different opinions.

Maybe — many pre-war flues here are unlined or have cracked clay tiles, and you can't tell from the hearth. A camera inspection settles it in about twenty minutes. If it's sound, we document that and sweep it. If it needs a liner, we price it plainly and tell you what's safe in the meantime, which is sometimes nothing until it's fixed.

Inspection first, always — it sets the sequence. Typically: chimney safety items before burn season, attic air-sealing and insulation in spring or summer when it pairs naturally with duct sealing, and the dryer vent the same day as everything else since it takes the least time. Masonry repairs cure best in warm, dry months, so we slot those accordingly.

Yes — our crews cover Alamo Heights's 1 ZIP code across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights, plus the surrounding communities.

We offer same-week scheduling across Alamo Heights, booked by a real person in under two minutes, 7 AM to midnight every day.

Alamo Heights is San Antonio's historic affluent enclave — 1920s-40s Spanish-revival and brick mansions near Olmos Park. The work here is period-correct masonry repointing, clay-liner relining, and crown rebuilds on chimneys approaching a century old. Either way it's one trip: a cross-trained crew bundles the chimney service with the vent and duct work on a single visit. Pilot Assembly Replacement is part of keeping that local housing stock safe, efficient, and up to code.

Pilot Assembly Replacement in Alamo Heights starts from $215, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8094 for a free, no-pressure Alamo Heights quote.

Yes — we run same-week and emergency pilot assembly replacement across Alamo Heights, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8094 and we prioritize Alamo Heights dispatch so a craftsman is on it fast.

Our Alamo Heights crew lives in and works the metro across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights — a certified, local pilot assembly replacement team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8094.