Skip to main content
Service area · 60 ZIP codes · 8 neighborhoods

Austin, TX

Full chimney services across all of Austin — 975k residents, every neighborhood covered. CSIA-certified, same-week scheduling.

975k
Residents in metro
60
ZIP codes covered
8
Neighborhoods
2 min
Human reply · 7 AM – 12 AM
Neighborhoods

Every neighborhood in Austin.

We service every neighborhood and ZIP in Austin. Find yours below or just give us a call — we'll confirm coverage and schedule on the spot.

Tarrytown
Hyde Park
Travis Heights
Mueller
Westlake
Barton Hills
Allandale
Circle C

Don't see yours? Call (214) 444-8094 — if it's in Austin, we cover it.

Local profile

Why chimney work in Austin is local.

Austin runs from historic bungalows in Hyde Park and Travis Heights to limestone Hill Country estates in Westlake and a flood of new-build east and north. The dominant work splits between prefab cap-and-chase on the new stock and crown rebuilds after Central Texas's periodic hard freezes. Across both, we send a single cross-trained crew so the chimney, vent and ducts are handled together, not booked as three appointments.

TarrytownHyde ParkTravis HeightsWestlake

Climate & code file · Greater Austin

Central Texas hands a homeowner four chimney problems on one chemistry — limestone and lime mortar that breathe and erode unlike hard Portland mix; cedar (Ashe juniper) that drops resinous needles on caps and burns hot and fast in the firebox; flash-flood downpours that dump months of rain in an afternoon onto crowns that bake dry the rest of the year; and mild winters that leave a flue idle ten months before it's lit hard for six weeks. Texas Service Experts meets all four with one cross-trained crew on one visit — masonry, sweep, cap and vent — so an Austin-metro homeowner solves the whole cycle in a single window instead of booking a mason, a sweep and a vent tech separately.

01

Limestone & lime mortar — the one that matters most

If your Austin chimney is older Hill-Country masonry, do not let a generalist repoint it with hard gray Portland. Soft limestone was laid in a breathable, high-lime mix that flexes with the stone; modern Portland is harder than the stone around it, so it transfers stress into the limestone and drives the cracking into the face — turning a repointing job into a stone-replacement job. The crew that reads the existing mortar, matches its composition and color, and repoints to move with the wall is the same crew already on site for the sweep and the cap — so the masonry, the flue and the venting are handled together, not by three callouts. That's the question budget crews don't even know to ask.

02

Cedar (Ashe juniper)

Cedar needles and the heavy December–February pollen pack into spark screens and crown washes — a clogged cap is a draft problem and a fire-screen failure at once. The same resinous debris finds the dryer vent and the gutters, so the crew clears the cap, checks the vent and flags the buildup in one pass rather than sending you back to the phone. On wood-burners we also flag cedar's hot, fast, resin-heavy burn: it glazes a flue far quicker than seasoned oak, so a cedar-burning Austin home needs a tighter sweep interval, not the generic annual default.

03

Flash floods

Hill-Country rain doesn't drizzle — it arrives in inches-per-hour walls that test a crown and flashing seal the way ten dry months never do. The leak you didn't know you had announces itself in the first big storm, often as a stain a room away from where the water actually enters. We trace the true entry point with a moisture meter and controlled water test before recommending a fix, then waterproof and re-flash before spring storm season — and while we're on the roof the cap and chase cover get sealed in the same trip, so the whole top of the system is watertight after one visit rather than after the ceiling stains.

04

Long dormancy

A Austin flue may sit unused for ten months, then get lit hard for six weeks — long enough for animals to nest, debris to collect, and a hairline crown crack to go unnoticed. One fall visit covers it all: sweep-and-scan the flue, clear the cap, and check the vent that's been idle just as long — so your first cold-front fire is on a verified, clean, code-ready system rather than a string of separate pre-season errands.

Code note · Greater Austin

Hill-Country code reality: soft limestone must be repointed in a breathable, high-lime mix — hard gray Portland is harder than the stone and drives the cracking into the face — and waterproofing belongs before the spring flash-flood season, not after the ceiling stains.

All services

Services in Austin.

Chimney Sweep

Annual flue cleaning, knocked out on the same visit as your other home jobs.

From $159

Chimney Inspection

A thorough safety + code check that maps every issue in one walk-through.

From $99

Chimney Cap

The small cap that keeps rain, animals, and embers out — fitted while we're up there.

From $275

Chimney Liner

Reline the flue once, correctly — the foundation the rest of the system relies on.

From $2,650

Chimney Restoration

Crown, masonry, cap, flashing, and waterproofing — all fixed in one coordinated project.

From $850

Chimney Crown

Seal the cracked crown before water turns it into a full restoration.

From $325

Chimney Waterproofing

Breathable whole-stack sealing that sheds rain while letting the masonry dry.

From $325

Throat Damper Replacement

Replace a cracked or warped throat damper with a new cast-iron assembly, set in refractory mortar.

From $375

Fireplace Services

Wood, gas, or electric — install, repair, and maintenance from one team.

From $2,100

Smoke Chamber Restoration

Re-parge the smoke chamber so the fireplace drafts right and burns clean.

From $725

Deep Chimney Cleaning (PCR)

Powered rotary tooling and PCR poultice for the glazed creosote a sweep can't budge.

From $475

Chimney Tuckpointing

Re-point crumbling mortar joints to lock the brick and shed water again.

From $675

Chimney Flashing Repair

A real two-layer flashing fix where the chimney meets the roof — not a caulk smear.

From $500

Chimney Masonry Repair

Rebuild cracked, spalling, or shifted brick back to a sound, code structure.

From $1,000

Chimney Framing Repair

Repair the wood chase framing that water, animals, or fire have eaten into.

From $850

Chimney Framing Rebuild

Full code-compliant chase rebuild — framing, siding, and cover by one crew.

From $3,400

Chimney Siding Replacement

Fresh Hardie, vinyl, or metal siding on the chase — matched to the house.

From $1,250

Chimney Exterior Wood Replacement

Swap out rotted fascia, trim, and corner boards around the chase — painted to match.

From $675

Chimney Flue Installation

A brand-new flue, spec'd to your fuel and height, permits and all.

From $2,950

Flexible Chimney Liner Installation

316Ti or 304 stainless flex liner that snakes through offsets a rigid liner can't.

From $2,200

Chimney Vent Installation

Proper B-vent, direct-vent, or Class A venting routed and terminated to code.

From $1,250

Spark Arrestor Installation

Ember-stopping mesh sized to NFPA 211 — a quick add when we're already up top.

From $225

Chimney Nest Removal

Humane nest removal, flue cleanup, and a cap so it doesn't happen again.

From $275

Brick Waterproofing

ChimneySaver vapor-permeable sealant that protects brick without trapping moisture.

From $450

Interior Wall Damage Repair

Patch the stained drywall a chimney leak left behind — and fix the leak too.

From $400

Downdraft Repair

Track down why smoke rolls into the room — usually a whole-house airflow issue.

From $300

Smoke Chamber Cleaning

HEPA-clean the corbeled smoke chamber that collects creosote fastest.

From $200

Smoke Chamber Rebuild

Rebuild a failed smoke chamber to NFPA 211 — better draft, far less creosote.

From $1,500

Smoke Chamber Repair

Spot-fix failed parging in the smoke chamber — the code violation we catch most.

From $550

Electric Fireplace Installation

Wall-mount, insert, or freestanding electric — wiring, framing, and trim handled.

From $675

Electric Fireplace Repair

Heater, blower, remote, or flame-effect acting up? One tech sorts it out.

From $179

Gas Fireplace Repair

Pilot won't hold, no heat, gas smell — diagnosed and repaired in one trip.

From $200

Fireplace Masonry Repair

Repair cracked firebrick before heat finds your framing.

From $575

Refractory Panel Repair

Seal hairline cracks in refractory panels before they force a replacement.

From $250

Refractory Panel Replacement

Exact-match OEM panels for every common DFW factory-built firebox.

From $725

Gas Burner Installation

A complete burner-and-log install — gas line, valve, ignition, controls.

From $900

Gas Valve Repair

Sticky, leaking, or failed gas valve — diagnosed and IFGC-tested.

From $225

Gas Valve Replacement

When a gas valve's past repair, a clean OEM-compatible assembly swap.

From $450

Glass Door Installation

Glass doors that cut draft loss, add a safety barrier, and finish the hearth.

From $625

Vented Gas Logs Installation

The most realistic flame and ember bed — installed with the damper set right.

From $975

Ventless Gas Logs Installation

All the heat stays in the room — installed with the required safety checks.

From $925

Pilot Light Installation

Turn a match-lit log set into a proper pilot ignition system.

From $300

Pilot Assembly Replacement

A clean full-assembly swap when the pilot gets weak or contaminated.

From $225

Remote Control Install

Ditch the wall key — go handheld remote, thermostat, or Wi-Fi control.

From $250

Pellet Stove Installation

Complete pellet stove setup — hearth, venting, air kit, electrical, all in one.

From $1,500

Pellet Stove Repair

Auger, igniter, blower, or board acting up? Fixed, with a cleaning included.

From $200

Pellet Stove Inspection

The annual NFPA 211 check (and cleaning) many insurers require.

From $139

Dryer Vent Cleaning

Clear the lint-packed dryer vent — perfect to pair with your chimney sweep.

From $159

Dryer Vent Inspection

Airflow + code check with a written report for insurance or HOA.

From $89

Air Duct Cleaning

NADCA-method whole-home duct cleaning — cleaner air, lower energy bills.

From $450

Air Duct Services

Beyond cleaning — duct repair, mastic sealing, sanitizing, and replacement.

From $300

UV Light Air Sanitization

Chemical-free UV-C lamps that keep the coil — and your air — clean.

From $575

Dual-Lamp UV-C System

Coil lamp plus an air-stream lamp for systems that need both.

From $850

Blown-In Insulation

Top off the attic to R-38 or R-49 and stop paying to heat the sky.

From $1,500

Spray Foam Insulation

Closed-cell or open-cell foam for the spots blown-in can't reach.

From $2,350

Attic Insulation Inspection

Find out your real R-value and where the attic is leaking air.

From $99

Insulation Services

Whole-home insulation retrofits — walls, crawl space, chase, and more.

From $900

Handyman Services

The little punch-list jobs handled while we're already at your home.

From $149

Chimney Leak Diagnosis

Find where the water actually gets in — with metering and zoned hose testing.

From $99

Chase Cover Replacement

Custom stainless or copper chase cover, formed to drain — not the rusting galvanized one.

From $275

Wood-to-Gas Fireplace Conversion

Real fire from a wall switch — an engineered conversion, not just a burner drop-in.

From $2,100

Above-Roofline Chimney Removal

Take the dead stack down to the deck and close the roof like it was never there.

From $1,600

Full Chimney Removal to Foundation

Cap-to-footing removal with the wall, floor, and gas all finished by one crew.

From $3,700

Chimney-Breast Removal & Structural Infill

Reclaim the bulkhead square footage — supported, framed, and finished flush.

From $1,900

Flue Capping & Fireplace Decommission

Retire a fireplace in place — sealed, gas-capped, and documented.

From $475

Custom Masonry Fireplace Build (Rumford)

A from-scratch masonry fireplace, including Rumford designs, engineered to draft.

From $8,400

Zero-Clearance Firebox Installation

A UL-listed firebox set strictly to its listing — chase, venting, and all.

From $4,700

Outdoor Fireplace & Fire-Feature Build

An outdoor fireplace or fire feature built to survive sun, rain, and freeze-thaw.

From $6,300

Wood-Fired Pizza Oven Build

A refractory-dome pizza oven that actually holds heat and drafts right.

From $5,300

Gas & Wood Fire-Pit Installation

Gas or wood fire pit that lights reliably and is built to be safe.

From $950

Chimney Asbestos & Lead Abatement

Licensed, contained asbestos and lead removal — clearance-tested before any other work.

From $1,250

Carbon Monoxide Diagnosis & Combustion Safety

Instrument-verified combustion safety — the whole-house view, not a guess.

From $375

Smoke, Soot & Puffback Remediation

Soot and odor removed across firebox, ducts, and surfaces — not just masked.

From $850

Fireplace Refacing — Stone & Brick Veneer

Stone or brick veneer refacing done by masons who respect a working firebox.

From $2,650

Whitewash, Limewash & German Smear

Whitewash, limewash, or German smear that breathes and ages gracefully.

From $625

TV-Over-Fireplace Heat Management & Mantel

Mount the TV over the fireplace without slowly cooking your electronics.

From $725

Open-Fireplace to Insert Conversion

Convert an open fireplace into a sealed, high-efficiency insert that gives heat back.

From $3,700

Emergency Storm Board-Up & Weather Seal

Stop the storm damage tonight, then fix it right — same team for both.

From $425

Emergency Smoke-Back & Flue-Blockage Clearing

Smoke rolling into the room? We clear the flue fast and confirm it drafts.

From $375

Leaning Chimney Emergency Bracing & Re-Anchor

Shore the leaning stack now, then re-anchor it right — one crew, both steps.

From $1,600

Stuck-Damper & Gas-Smell Emergency Response

Stuck damper or gas smell near the fireplace — answered fast and resolved properly.

From $325

Level 1 Chimney Inspection

The annual baseline NFPA 211 calls for when nothing about the system has changed.

From $139

Level 2 Chimney Inspection

Camera-scanned — the tier required at sale, after a fire, or on any fuel change.

From $300

Level 3 Chimney Inspection

The invasive tier — opening finish or masonry to reach a hazard a camera found but could not evaluate.

From $950

Real Estate Transaction Report

A Level 2 packaged for a Texas option period — dated written report included.

From $350

Damper Repair

Free, re-seat, or re-cable a damper that still has real life left in it.

From $159

Top-Sealing Damper Installation

A rubber-gasket damper at the crown that actually seals — unlike any throat damper.

From $475

Chimney Crown Rebuild

A poured reinforced crown with overhang and drip edge, replacing the mortar wash that failed.

From $1,250

Chimney Rebuild Above Roofline

Rebuilt from the roof line up, on a base that is still sound.

From $1,550

Full Chimney Rebuild

Stack rebuilt from the firebox or foundation up — quoted after a structural assessment.

From $3,700

Chimney Cap Repair

Re-secure, re-screen, or re-weld a cap that is genuinely worth saving.

From $189

Chase Cover Repair

Seal and re-flash the cover before the framing underneath pays for it.

From $250

Multi-Flue Chimney Cap

One fabricated lid covering every flue and the whole crown at once.

From $625

Gas Fireplace Diagnostic

Find the fault first — the fee comes off the invoice when you approve the repair.

From $99

Gas Fireplace Annual Service

Burner, pilot, glass, gasket, and a combustion check — once a year, like a furnace.

From $159

Rigid Stainless Liner

Rigid stainless for a straight flue — heavier, smoother, longer-lived than flex.

From $2,000

Cast-In-Place Liner

A poured masonry liner that seals the flue and stiffens a tired stack from the inside.

From $3,700

Smoke Chamber Parging

Smooth the corbelled smoke chamber to code with refractory mortar.

From $725

Animal Removal & Exclusion

Removal plus the guard that stops the next one from moving in.

From $250

Breathable Water Repellent

Vapor-permeable repellent — never a film-forming sealer that traps moisture in the brick.

From $450

Fireplace Insert Installation

Labor to set and connect your insert — unit priced separately, liner itemized.

From $950

Wall Vent Cap Replacement

Swap the brittle, lint-jammed wall cap for a damper that closes again.

From $169

Roof Jack / Vent Cap Replacement

A new roof termination, flashed into the shingles the way it should have been.

From $375

Dryer Vent Repair

Crushed flex, pulled joints, foil duct, screws in the run — replaced with smooth rigid metal.

From $200

Duct Sealing (Aerosol)

Seal the leaks from inside the duct system — with a measured before-and-after number.

From $1,900

Duct Repair & Replacement

Torn, disconnected, crushed, or undersized runs — rebuilt so the room finally gets air.

From $525

Evaporator Coil & Blower Cleaning

Clean the two parts nobody looks at — the coil and the blower wheel.

From $375

Filtration Upgrade (Media Cabinet)

Trade the one-inch compromise for a media cabinet sized to your actual airflow.

From $575

Prices shown are starting estimates and may change with the condition, access, and scope we find on site. Only a written quote from an on-site visit is a price we commit to.

Call us
(214) 444-8094
Hours
Mon–Sun 7:00 AM – 12:00 AM
Open Sunday 7:00 AM – 12:00 AM
HQ
Dallas, TX
2911 Turtle Creek Blvd, Suite 300

Last reviewed:

10+
Years
NFPA 211
Standard
CSIA
Certified
< 2hr
Response
Ready when you are

Talk to a CSIA-certified expert today.

Free written quote. Same-week scheduling. 24/7 emergency response when you need it.

Licensed & Insured Same-Week Scheduling Written Quote, Always
Emergency

24/7 Response

Active leak, animal in flue, post-fire damage, or smoke event? Real humans on the line 7 AM to 12 AM every day — replies in under 2 minutes. Tech dispatch within 2 hours during business hours, subject to crew availability after-hours.

Emergency line
Call NowBook